Fill out your e-mail addressto receive our newsletter!
2014 Ky. RT. 825
Hager Hill, KY. 41222
Bridal Sash Kit Includes:
Your choice of ribbon color.
Heat sealed ends on your ribbon for no fraying or purchase Rhinestone ends.
Simply choose your ribbon color from the drop down menu below.
Then choose the cut you want your Ribbon Ends from the next drop down menu.
Your Bridal Sash will be a 3 yard piece of Two Inch Wide Beautiful Double Faced Satin Ribbon.
You can choose from slanted cut, straight cut, v-cut or rhinestone edge in 3 or 4 row. Our Ribbon ends are sealed so that they will not fray. Rhinestone ends are straight. Rhinestone ends can be added to this kit but they are not added to the ribbon.
If you are interested in our rhinestone ends see below some photos of how they are added to the sash. These ends can be purchased separate or in a bridal sash kit. Here are the directions on how to apply them.
Fold the end in half and lay your ribbon in between. Lay a thin towel over it and set a hot iron high setting on it for approximately 5-10 seconds. Check to see if the rhinestones are holding good to the ribbon. Try to lift the rhinestones from the ribbon, if you can not pull them from the ribbon then they are set. Turn the ribbon over and repeat this process on the other side.
Tips: Always make sure your rhinestone end is trimmed well so no plastic shows on the ribbon. Be careful and get your rhinestone ends straight on your ribbon. Do not iron back and forth just set the iron directly down on the towel. If your rhinestones do not look straight enough when you first remove the iron you can push them a little to straighten. They do not move easy, it takes some hard pushing but they will move a little while the plastic is drying to the ribbon.
If you are interested in adding an applique to your ribbon Bridal Sash that is easy to do. Simply order the applique of your choice separate from this listing and apply it to the ribbon by sewing, glue or ironing it on. Application would depend on the applique you choose. Many of our appliques are iron on. Most of our rhinestone appliques have a hot fix backing which can be ironed on. If the applique does not have the plastic it will be a mesh fabric backing. This type of applique would have to be applied with glue or sewing. If you order a metal back applique these are sew on only. They are all very simple to apply.
Tips: If your applique has the plastic like backing it is iron on. The easiest way to apply is ironing. Turn your applique over and iron from the back side. Be very careful to get your ribbon straight, lay a thin towel over the ribbon and bring your iron directly down on the ribbon. Do not iron back and forth until the ribbon is attached good to the applique.
If you want to glue on an iron on applique you will need to also stitch it a little to make sure it holds to your ribbon good because the layer of plastic on the back of the applique should not be removed and the plastic backing can pull away from the applique. We suggest you iron on.
If your applique does not have the plastic backing then it is a sew on or glue on applique, that is your choice. We do sell many different kinds of glue.
If the applique is metal back the best way is to stitch it on. Metal back appliques are beautifully made and look like jewelry but keep in mind that they are a little heavier and a little more fragile to work with.
First Step we cut the rhinestones to fit your ribbon and trim the edges carefully.
We have chosen our 2 inch Antique white satin ribbon and cut and trimmed our silver
crystal 4 row rhinestone end.
Fold the rhinestone end in half.
Lay the ribbon neatly inside and fold over.
Try to keep the ribbon as straight as possible before ironing.
Lay a towel over the rhinestone end and place iron straight down on towel.
See how beautiful your rhinestone ends can look! This is 4 Row.
See here the difference between 3 row and 4 row.
Choose your ribbon color from the drop down menu below.
There are no reviews for this item. Be the first to review it!